Skip to content

HDMI Expansion Card fails DP alt-mode negotiation on Core Ultra 13 (ucsi GET_CABLE_PROPERTY failed, -5); only suspend/reboot recovers #89

Open

Description

@HmonWutt

System information

  • Laptop: Framework Laptop 13 (Intel Core Ultra Series 1, Core Ultra 5 125H)
  • OS: Arch Linux (fully up to date)
  • Kernel: 7.3.4-arch1-1 (i915 in use)
  • BIOS: Intel Management Engine 0.0.0.2141 (via LVFS, all firmware current)
  • HDMI Expansion Card firmware: 3.0.16.106 (bootloader 3.0.2.900, serial 11AD1D009E5C3F0B18220B00)
  • Desktop: i3 on X11

Summary

Connecting a display to the HDMI Expansion Card frequently fails: the GPU never sees the connector and the TV reports "no signal". The kernel repeatedly logs UCSI failures:

[  254.504236] ucsi_acpi USBC000:00: unknown error 256
[  254.504250] ucsi_acpi USBC000:00: GET_CABLE_PROPERTY failed (-5)

These errors appear at (or shortly after) boot and repeat on every replug attempt.

Observed state when it fails

  • The card's USB function re-enumerates normally on each replug:
    usb 3-4: New USB device found, idVendor=32ac, idProduct=0002
    usb 3-4: Product: HDMI Expansion Card
    hid-generic 0003:32AC:0002.XXXX: hiddev96,hidraw0
    
  • The Type-C partner advertises DisplayPort alt mode (SVID ff01, number_of_alternate_modes: 2), but the mode is never entered:
    $ cat /sys/class/typec/port2-partner/port2-partner.1/active
    no
    
  • All DP connectors remain disconnected:
    $ cat /sys/class/drm/card1-DP-1/status
    disconnected
    
  • Forcing a connector re-probe does not help:
    $ echo detect > /sys/class/drm/card1-DP-1/status   # (as root, succeeds, no change)
    
  • Writing to the alt mode active file is not possible from userspace (read-only).

What does / does not recover it

  • Does NOT work: replugging the HDMI cable, reseating the expansion card in the same port, forcing connector re-detect via sysfs, xrandr mode changes (connector never becomes visible).
  • DOES work (workaround): systemctl suspend + resume — UCSI re-initializes on resume and the display negotiates correctly. A full reboot also works but is slower.

This suggests the UCSI PPM/connector state gets wedged during initial negotiation and only a controller re-initialization (ACPI resume / reboot) clears it.

Steps to reproduce

  1. Boot the laptop with the HDMI Expansion Card seated and a display connected via HDMI (or connect the display shortly after boot).
  2. the display shows "no signal" and the UCSI errors above appear in dmesg.
  3. Any replug of cable or card logs unknown error 256 / GET_CABLE_PROPERTY failed (-5) again.
  4. systemctl suspend + wake resolves the issue; the display is then detected and works at its preferred mode until the next occurrence.

Expected behavior

DP alt mode should negotiate (or retry) automatically when the display is connected; GET_CABLE_PROPERTY should not fail persistently with -EIO.

Activity

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Metadata

Metadata

Assignees

No one assigned

    Labels

    No labels
    No labels

    Type

    No type

    Projects

    No projects

      Milestone

      No milestone

      Relationships

      None yet

      Development

      No branches or pull requests

      Issue actions